Kanga farm equipment S Range Rotary Cutters are general-purpose implements designed and engineered to thrive in harsh Australian conditions.
Our S Range Rotary Cutters boast a rugged 3mm deck, fully reinforced underneath, ensuring exceptional strength and longevity. This robust construction enhances durability and creates a clean-top design that minimises debris and water collection; keeping your implement in prime condition even in the harshest environments.
The lowered high-tensile cutter bar allows a higher volume of material to discharge efficiently, producing fast, clean and dependable cutting in light scrub, regrowth and long grass.
Features
Construction
3mm, round-back, clean-top deck
- Round-back increases maneuverability
- Clean top reduces the collection of debris and water
Deck side walls are welded and braced for strength when turning
Gearbox mounting plate is welded to the subframe, creating greater structural integrity, in the event of load torque caused by blade impact
Deck is hot-dip galvanized, for superior corrosion resistance and longevity
Cutter Bar & Blades
Cutter bar
- Lowered, bolt-together, sandwich design
- 100mm wide, high-tensile steel
- Powered by T piece with drive lugs
Blades
Countersunk blade bolt design avoids wear and tear. Unfasten the lock nut to replace blades throughout the lifetime of the implement
Two (2) stepped, suction, spring steel blades pivoting on hardened bushes
Blade bolt inspection cap allows operator to check blades and blade bolts from the top of the implement
Skids & Cutting Height
Skids
- Reversible, removable side skids with tapered leading and trailing edges
- Braced for strength
- Positive-locking with individual bolt holes to maintain height
- Adjustable, four (4) positions in 30mm increments
Cutting height
50, 80, 110 and 140mm cutting heights
3-Point Linkage Information
Category 1 and 2 linkage
Two-plate, double clevis mount designed to absorb lateral load and decrease metal fatigue when turning
Multi-position sliding tower
- In the centre-mounted position the implement is directly behind the tractor
- In the offset position, the implement extends out left or right
- Tower chain mounting points are welded to the deck and subframe
- Chain stays allow for tower movement, forward and aft, to maintain an even cut over undulating ground
PTO & Protection
PTO
Series 4 with 150mm (6″) friction clutch
Lever release PTO Shaft Guards facilitate safe engagement of yokes and easy joint maintenance
Protection
Front and rear chain curtain is incorporated into the deck for maximum safety, with a wire rope replacement system for easy replacement
Blade exclusion zone for safety to prevent accidental contact with blades
Waterproof manual holder
Specifications
Code | KSSR120 | KSSR135 | KSSR150 |
Size Reference | 1.2m | 4’0” | 48” | 1.35m | 4’6” | 54” | 1.5m | 5’0” | 60” |
Tractor Range (hp) | 28-40 | 23-33 @ PTO | 35-50 | 25-42 @ PTO | 40-50 | 33-42 @ PTO |
Gearbox | 40hp, 540rpm, 1:1.93 ratio | 40hp, 540rpm, 1:1.93 ratio | 40hp, 540rpm, 1:1.93 ratio |
Blade Tip Speed (ft/min) | 13,119 | 14,760 | 16,400 |
Overall Width (mm) | 1410 | 1560 | 1710 |
Cutting Width (mm) | 1200 | 1350 | 1500 |
Weight (kg) | 250 | 280 | 300 |
Options
KANGA light-duty depth wheel
- 360° spinning wheel fork
- Segmented rubber wheel assembly
- Rectangular tube frame
- Nyloc lock nut to set pre-load on load bearing turn table discs
- Grease nipples for turn table discs and fork shaft for easy regular maintenance